Perle eX-KIT11-S110-BNC - Fast Ethernet Extender Kit

10/100 Ethernet Copper Extender

When you need to extend Ethernet services beyond the general IEEE 802.3 limits of 328ft, and new fiber cabling is cost prohibitive, the EX-KIT11-S110-BNC Fast Ethernet Extender Kit is the perfect solution because Perle Ethernet Extenders transparently extend 10/100 Ethernet connections across copper wiring.  Use single twisted pair or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV, and CATV applications.  These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, connecting a remote office or private-network backbone to a corporate LAN- anywhere you need Ethernet communication links between separated LANs or LAN devices.  Perle's advanced features such as Link Pass-Through, Interlink Fault Feedback, and Loopback allow Network administrators to "see everything" for more efficient troubleshooting and less on-site maintenance.  These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make the EX-KIT11-S110-BNC Fast Ethernet Extender Kit the smart choice for IT professionals.

• 1 Pair of eX-1S110-BNC Fast Ethernet Extenders
• Extend 10/100Base-TX Ethernet up to 10,000 feet over 2-wire 24 AWG twisted pair
• Hi-Speed - up to 200+ mbs aggregate line rate
• Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes
• 1 10/100 Ethernet port per extender
• Advanced features including Link Pass-Through, Interlink Fault Feedback, Plug and Plan, Auto-MDIX and Loopback

• Extend Ethernet Over Twisted Pair - Extend an Ethernet link over category 5e, 6, and 7 cabling up to 10,000 feet.
• Extend Ethernet Over Coaxial Cable - Extend an Ethernet link over 75 ohm coaxial cable. 
• Hi-Speed Performance - Utilizes second generation VDSL2 technology (ITU-T Recommendation G.993).  When operating under "Profile 30a", Perle Ethernet Extenders can provide an aggregate VDSL line rate capability of over 200 mbps.  (Actual distance and performance may vary depending on the type/gauge and condition of the wire used. )
• Plug and Play Operation - Perle Ethernet Extenders will automatically configure your VDSL interlink connection.  The CO/CPE peer association will be determined automatically by the Ethernet Extender.  No need to set CO/CPE VDSL pairing.  Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
• Link Pass-Through - With Link Pass-Through the state of the 10/100Base-TX Ethernet connection is "passed through" the VDSL link to the 10/100Base-TX Ethernet connection on its remote peer.  A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.  Competitive Ethernet extenders without this feature will never detect or report any error conditions.
• Interlink Fault Feedback - Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100 Ethernet ports on each end until the link recovers.
• Auto-Negotiation - The Ethernet Extender supports auto negotiation on the 10/100Base-TX interface.
• Auto-MDIX - Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
• Fixed Speed and Duplex - Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate.  By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
• VLAN - Transparent to tagged VLAN (802.1Q) packets.
• Transparent to IP Video Compression Protocols - Fully transparent to such IP video compression schemes such as MPEG-4, H.264, and MJPEG.
• Power Strain Relief Strap - A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender.  Ideal for areas that may be exposed to vibration.
• Loopback - When enabled, will perform a loopback on the copper VDSL Interlink.

NOTE: The following specifications are for 1 eX-1S110-BNC Extender only.  The EX-KIT11-S110-BNC Fast Ethernet Extender Kit comes with a pair of eX-1S110-BNC Ethernet Extenders.

• Color:  Black
• Weight: 0.66 lbs
• Dimensions: 4.7" x 3.1" x 1.0" (L x W x D, Approx)

Ethernet

• Port: 1 port RJ45 - 10/100Base-TX - Shielded
• Auto-MDIX: Auto-MDIX enables proper operation with either straight-through or corssover cabling
• Distance:Distance up to 328 ft. as per IEEE 802.3
• Maximum Frame Size: 1522 bytes

VDSL-Interlink

• BNC: Coaxial 75 ohm cable with BNC connector
• Cabling: Ethernet Extenders must be connected in pairs using unconditioned wire between 19 and 26 AWG.  Circuits that run through signal equalization equipment are not permitted.
• VDSL2 Line Rate/Reach: Actual distance and rates experienced will depend on condition and gauge of wire used.

Power

• Input Supply Voltage: 9-30 vDC, unregulated (12 vDC Nominal)
• Current: 320 mA 
• Power Consumption (watts): 3.8
• Power Connectors: 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block 

Power Adapter

• Universal AC/DC Adapter: 100-240v AC, regulated 12v DC adapter included

Indicators

• Power/TST: Green LED is turned on when power is applied to the Ethernet Extender.  Otherwise it is off.  The LED will blink when in Loopback test mode.
• CO-Local: Ethernet Extender is operating in CO VDSL mode
• CPE-Remote: Ethernet Extender is operating in CPE VDSL mode
• ILNK: Indicates Link Status and activity on the Interlink (VSDL) port
• ETH: Indicates link status and activity on Ethernet port(s)

Switches - Accessible through a side opening in the chassis

• Rate/Reach: Two switches enable the user to select the right balance between speed and distance for their environment.
• Signal to Noise Ratio: Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB.  The higher SNR number provides better impulse noise protection but lowers performance.
• Auto-Negotiation (802.3u): Enabled (Default)- The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100Base-TX interface.  It is set to advertise full duplex.  Disabled- The Ethernet Extender sets the port according to the position of the speed and duplex switches.
• Link Mode: Standard (Default)- The 10/100Base-TX link remains active independent of the state of the Ethernet link on its remote peer.  Link Pass-Through- The state of the 10/100Base-TX Ethernet connection is "passed through" or propagated across the VDSL link to the 10/100Base-TX Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.
• Interlink Fault Feedback: Enabled- A loss of VDSL link will drop the 10/100 Ethernet port on each end until link recovers.  Disabled (Default)- The state of the VDSL link is not propagated to the 10/100Base-TX port.
• Loopback: Enabled- The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.  Disabled (Default- UP).
• Set Ethernet Speed (Port 1): When Auto-Negotiation switch is disabled, fixed speed can be set: 100 (Default) or 10
• Set Ethernet Duplex (Port1): When Auto-Negotiation switch is disabled, Duplex can be set: Full (Default) or Half

Environmental Specifications

• Operating Temperature: 0°C to 50°C (32°F to 122°F)
• Storage Temperature: minimum range of -25°C to 70°C (-13°F to 158°F)
• Operating Humidity: 5% to 90% non-condensing
• Storage Humidity: 5% to 95% non-condensing
• Operating Altitude: Up to 3,048 meters (10,000 feet)
• Heat Output (BTU/HR): 13.1
• MTBF (Hours): Without power adapter- 468,351;  With power adapter- 289, 015

Regulatory Approvals

• Emissions: FCC Part 15 Class A, EN55022 Class A; CISPR 22 Class A; EN61000-3-2
• Immunity: EN55024
• Electrical Safety: UL 60950-1; EN60950;  CE
• Environmental: RoHS, WEEE and Reach compliant
• Other: ECCN 5A991A;  HTSUS Number 8517.62.0050
• Warranty: Lifetime Limited Manufacturer Warranty

Be the first to review this product. Write a Review

Shipping Restrictions

• This item cannot be shipped to PO Boxes.
• This item can be shipped only within the U.S.

Special Order Item

This item ships directly from the manufacturer and is not stocked in our warehouse. If stock is available at the manufacturer, the item will ship directly to you, usually within 7 - 15 business days.

Once the order has been sent to the manufacturer it can no longer be canceled.

If payment is made via credit card it will be charged before the order is sent to the manufacturer.

You must contact the manufacturer directly regarding returns and defective items.

We will contact you by email if the item is sold out or backordered (and we were unable to update the site before you placed the order) or if the item will be delayed longer than expected.

We have no control over the speed of the manufacturer's order processing, or whether they will honor your request to ship the item by any particular method.

• UPC: 679202038144 
• Mfr's Part #: 06003814 

• Return Policy
• Shipping Methods
• Order Acceptance Policy